鏡面輥做好保養工作，可以延長使用壽命。鏡面輥在使用過程中應該注意以下維護保養：1. 通常情況下;輥筒在裝入機架時;一般情況是不會任意拆下來的;但要將輥筒使用壽命延長;科學的方法是要將輥筒內的油類或水類放出;然后通入防銹類油品;當使用時將油品類再次放出;清潔及除油;然后按正常方式使用;2. 當輥筒使用前加溫或降溫;要將輥筒調整為慢速轉動;這有利于輥筒加溫或降溫時不會由其自重而產生降溫升溫不均勻而變形;是延長輥筒使用壽命的一類方式;3. 當輥筒拆下機架時;應將內部的水類清除;然后再將輥筒表面上防銹油或黃油類然后用PVC保護包裝后再用軟質類包裝理進行再包裝;這樣有利于保護超鏡面輥表面與空氣中的酸性或堿性氣體發生化學反應;叢而使得表面光潔度降低;嚴重者將使輥面報修;造成損失。